What is an ITP in construction?

An Inspection and Test Plan (ITP) is a quality assurance document used in construction to define inspection activities, hold points, and witness points at key stages of work. It specifies what needs to be checked, by whom, and records the results for audit and compliance purposes.

How much does HoldPoint QA cost?

HoldPoint QA charges $45 AUD per active project per month. There are no per-seat fees or per-document charges. Projects start as draft (free) until the first document is added.

Can external clients sign ITPs without an account?

Yes. HoldPoint QA sends a secure sign-off link via email. External signatories (clients, principal's representatives, or engineers), can review the full ITP checklist and sign digitally without needing an account or app.

Does HoldPoint generate ITP PDFs automatically?

Yes. When an ITP is approved, HoldPoint automatically generates a branded PDF containing all checklist results, inspection notes, photos, and signatures. PDFs are regenerated if any information changes.

Do I need an ITP for lifts & elevators work in Australia?

If your contract, principal contractor, or client QA manual calls for an Inspection and Test Plan, you need one, whether or not your scope is "construction" in the everyday sense. On commercial and government projects, lifts & elevators work is typically assessed against AS 1735 (Lifts, escalators and moving walks, NCC Volume 1) Access and egress, and State lift regulations, and the ITP is how you show each requirement was actually verified.

What hold points should a Lifts & Elevators ITP include?

At minimum: shaft and pit readiness inspection, load test and safety gear verification, and regulatory inspection before release. Hold points belong wherever a defect would be concealed by following work or expensive to put right, so work stops until the nominated party signs. Your specification or the principal's QA plan may add more.

Which standards apply to lifts & elevators inspections?

The references most lifts & elevators ITPs cite are AS 1735 (Lifts, escalators and moving walks, NCC Volume 1) Access and egress, and State lift regulations. Always check the project specification as well, it frequently calls up extra requirements, or a specific edition, on top of the standard.

Can I use an AI-generated lifts & elevators ITP on a real project?

Yes, as a starting point. Generate the lifts & elevators ITP for your scope, then review it against your contract and specification, especially the hold points, like shaft and pit readiness inspection. Run it through HoldPoint for digital sign-offs, photos, and branded PDFs, and have your QA manager or superintendent approve the final version before it goes to site.

Mechanical & building services

AI-powered · Free to try · Save your ITP

Free Lifts & Elevators ITP Generator

Generate a complete Inspection and Test Plan for lifts & elevators work in seconds. Installation, adjustment, load testing, and regulatory inspection checkpoints. Hold points and witness points are placed automatically, edit, brand, and sign off when you're ready.

Lifts & Elevators-specific hold points and witness points
Aligned with relevant Australian Standards
Sign up free to download your PDF
Save to your workspace and use on every project

Trade

Scope

Brand

Project

Finish

What trade is this ITP for?

We'll build a practical starter checklist for your trade, you can edit anything after.

Used on live Australian projects

Read their stories

Background

What is a Lifts & Elevators ITP?

A lifts & elevators ITP documents the inspection and testing steps for mechanical and building-services work, from rough-in and installation through commissioning, pressure tests, and handover sign-off.

On a lifts & elevators job the plan turns on a handful of mandatory stops: shaft and pit readiness inspection, load test and safety gear verification, and regulatory inspection before release. Each of those is a hold point: work doesn't move past it until the nominated party has inspected and signed. Witness points like guide rail installation, car assembly and alignment, and door operator adjustment tell the superintendent or client when to attend, without holding up the crew if they can't make it.

An Australian lifts & elevators ITP is normally written against AS 1735 (Lifts, escalators and moving walks, NCC Volume 1) Access and egress, and State lift regulations. Naming the standard you're inspecting to, rather than a generic "inspect and approve" line, is what makes the record hold up in an audit, a defect claim, or a payment dispute.

Quality checkpoints

Lifts & Elevators ITP Hold Points & Witness Points

The AI generator automatically includes these checkpoints based on your scope description. Hold points require mandatory sign-off before work proceeds; witness points notify the relevant party but don't stop work.

Hold Points

Work stops until signed off

Shaft and pit readiness inspection
Load test and safety gear verification
Regulatory inspection before release

Witness Points

Party notified, work can continue

Guide rail installation
Car assembly and alignment
Door operator adjustment
Emergency phone testing

Applicable Australian Standards

AS 1735 (Lifts, escalators and moving walks
NCC Volume 1) Access and egress
State lift regulations

Audit-grade evidence

GPS & weather captured at every lifts & elevators sign-off.

Generating a lifts & elevators ITP gets you a checklist. Defending it years later in a defect claim is a different problem. HoldPoint records the inspector's GPS coordinates and the live weather (temperature, humidity, wind, and sky condition), at the moment they sign each hold point. The data prints on the final PDF under the signature.

Temperature on record

Pour temp, ambient, and curing window, automatically logged.

Humidity & wind

Critical for paint, coating, and curing claims under AS standards.

Lat / lng + map link

Proof the inspector was actually on site, not signing from the office.

Available on every paid HoldPoint plan. The free generator gives you the ITP: HoldPoint gives you the defensible record.

Common questions

Lifts & Elevators ITP: Frequently Asked Questions

Do I need an ITP for lifts & elevators work in Australia?: If your contract, principal contractor, or client QA manual calls for an Inspection and Test Plan, you need one, whether or not your scope is "construction" in the everyday sense. On commercial and government projects, lifts & elevators work is typically assessed against AS 1735 (Lifts, escalators and moving walks, NCC Volume 1) Access and egress, and State lift regulations, and the ITP is how you show each requirement was actually verified.
What hold points should a Lifts & Elevators ITP include?: At minimum: shaft and pit readiness inspection, load test and safety gear verification, and regulatory inspection before release. Hold points belong wherever a defect would be concealed by following work or expensive to put right, so work stops until the nominated party signs. Your specification or the principal's QA plan may add more.
Which standards apply to lifts & elevators inspections?: The references most lifts & elevators ITPs cite are AS 1735 (Lifts, escalators and moving walks, NCC Volume 1) Access and egress, and State lift regulations. Always check the project specification as well, it frequently calls up extra requirements, or a specific edition, on top of the standard.
Can I use an AI-generated lifts & elevators ITP on a real project?: Yes, as a starting point. Generate the lifts & elevators ITP for your scope, then review it against your contract and specification, especially the hold points, like shaft and pit readiness inspection. Run it through HoldPoint for digital sign-offs, photos, and branded PDFs, and have your QA manager or superintendent approve the final version before it goes to site.

Related industries

More Mechanical & building services ITP Generators

Electrical ITP Generator

Generate a free electrical ITP with AI. Covers rough-in, cable containment, switchboard installation, testing, and AS/NZS 3000 compliance. PDF in seconds.

Generate

Plumbing & Hydraulics ITP Generator

Generate a free plumbing and hydraulics ITP with AI. Covers pipe installation, pressure testing, backflow prevention, and AS/NZS 3500 compliance. PDF in seconds.

Generate

HVAC & Mechanical Services ITP Generator

Generate a free hvac & mechanical services Inspection & Test Plan (ITP) with AI in seconds. Covers ductwork, plant install, refrigerant works, TAB, and commissioning hold points. Hold points, witness points, and PDF export, built for Australian QA workflows.

Generate

Fire Protection ITP Generator

Generate a free fire protection Inspection & Test Plan (ITP) with AI in seconds. Sprinklers, hydrants, detection, and commissioning aligned to AS 2118 and AS 1851. Hold points, witness points, and PDF export, built for Australian QA workflows.

Generate

Fire Alarm & Detection ITP Generator

Generate a free fire alarm & detection Inspection & Test Plan (ITP) with AI in seconds. Detection loops, EWIS, cause-and-effect, and witness testing before occupancy. Hold points, witness points, and PDF export, built for Australian QA workflows.

Generate

Refrigeration & Cold Chain ITP Generator

Generate a free refrigeration & cold chain Inspection & Test Plan (ITP) with AI in seconds. Coolrooms, panel install, refrigerant lines, and temperature mapping sign-off. Hold points, witness points, and PDF export, built for Australian QA workflows.

Generate

Browse all 91 industries →

Need to manage ITPs across a live project?

The free generator builds a single ITP. HoldPoint gives you the full workflow, templates, digital sign-offs, photo attachments, audit trails, and automatic PDF generation for every document on every project.

Continue with my ITP in HoldPoint Generate my Lifts & Elevators ITP

14 days free. No credit card to start.