What is an ITP in construction?

An Inspection and Test Plan (ITP) is a quality assurance document used in construction to define inspection activities, hold points, and witness points at key stages of work. It specifies what needs to be checked, by whom, and records the results for audit and compliance purposes.

How much does HoldPoint QA cost?

HoldPoint QA charges $45 AUD per active project per month. There are no per-seat fees or per-document charges. Projects start as draft (free) until the first document is added.

Can external clients sign ITPs without an account?

Yes. HoldPoint QA sends a secure sign-off link via email. External signatories (clients, principal's representatives, or engineers), can review the full ITP checklist and sign digitally without needing an account or app.

Does HoldPoint generate ITP PDFs automatically?

Yes. When an ITP is approved, HoldPoint automatically generates a branded PDF containing all checklist results, inspection notes, photos, and signatures. PDFs are regenerated if any information changes.

Do I need an ITP for glazing & facade work in Australia?

If your contract, principal contractor, or client QA manual calls for an Inspection and Test Plan, you need one, whether or not your scope is "construction" in the everyday sense. On commercial and government projects, glazing & facade work is typically assessed against AS 1288 (Glass in buildings, AS 2047) Windows and doors, and NCC weatherproofing, and the ITP is how you show each requirement was actually verified.

What hold points should a Glazing & Facade ITP include?

At minimum: subframe alignment inspection, structural glazing cure verification and water penetration test (if specified). Hold points belong wherever a defect would be concealed by following work or expensive to put right, so work stops until the nominated party signs. Your specification or the principal's QA plan may add more.

Which standards apply to glazing & facade inspections?

The references most glazing & facade ITPs cite are AS 1288 (Glass in buildings, AS 2047) Windows and doors, and NCC weatherproofing. Always check the project specification as well, it frequently calls up extra requirements, or a specific edition, on top of the standard.

Can I use an AI-generated glazing & facade ITP on a real project?

Yes, as a starting point. Generate the glazing & facade ITP for your scope, then review it against your contract and specification, especially the hold points, like subframe alignment inspection. Run it through HoldPoint for digital sign-offs, photos, and branded PDFs, and have your QA manager or superintendent approve the final version before it goes to site.

Construction & trades

AI-powered · Free to try · Save your ITP

Free Glazing & Facade ITP Generator

Generate a complete Inspection and Test Plan for glazing & facade work in seconds. Curtain wall, windows, structural glazing, and weatherproofing hold points. Hold points and witness points are placed automatically, edit, brand, and sign off when you're ready.

Glazing & Facade-specific hold points and witness points
Aligned with relevant Australian Standards
Sign up free to download your PDF
Save to your workspace and use on every project

Trade

Scope

Brand

Project

Finish

What trade is this ITP for?

We'll build a practical starter checklist for your trade, you can edit anything after.

Used on live Australian projects

Read their stories

Background

What is a Glazing & Facade ITP?

A glazing & facade ITP is a structured quality assurance document that defines every inspection and test required during glazing & facade works, who checks what, when work must stop for sign-off, and what evidence is recorded.

On a glazing & facade job the plan turns on a handful of mandatory stops: subframe alignment inspection, structural glazing cure verification and water penetration test (if specified). Each of those is a hold point: work doesn't move past it until the nominated party has inspected and signed. Witness points like sealant application, glass type verification and operable window tests tell the superintendent or client when to attend, without holding up the crew if they can't make it.

An Australian glazing & facade ITP is normally written against AS 1288 (Glass in buildings, AS 2047) Windows and doors, and NCC weatherproofing. Naming the standard you're inspecting to, rather than a generic "inspect and approve" line, is what makes the record hold up in an audit, a defect claim, or a payment dispute.

Quality checkpoints

Glazing & Facade ITP Hold Points & Witness Points

The AI generator automatically includes these checkpoints based on your scope description. Hold points require mandatory sign-off before work proceeds; witness points notify the relevant party but don't stop work.

Hold Points

Work stops until signed off

Subframe alignment inspection
Structural glazing cure verification
Water penetration test (if specified)

Witness Points

Party notified, work can continue

Sealant application
Glass type verification
Operable window tests
Protection prior to handover

Applicable Australian Standards

AS 1288 (Glass in buildings
AS 2047) Windows and doors
NCC weatherproofing

Audit-grade evidence

GPS & weather captured at every glazing & facade sign-off.

Generating a glazing & facade ITP gets you a checklist. Defending it years later in a defect claim is a different problem. HoldPoint records the inspector's GPS coordinates and the live weather (temperature, humidity, wind, and sky condition), at the moment they sign each hold point. The data prints on the final PDF under the signature.

Temperature on record

Pour temp, ambient, and curing window, automatically logged.

Humidity & wind

Critical for paint, coating, and curing claims under AS standards.

Lat / lng + map link

Proof the inspector was actually on site, not signing from the office.

Available on every paid HoldPoint plan. The free generator gives you the ITP: HoldPoint gives you the defensible record.

Common questions

Glazing & Facade ITP: Frequently Asked Questions

Do I need an ITP for glazing & facade work in Australia?: If your contract, principal contractor, or client QA manual calls for an Inspection and Test Plan, you need one, whether or not your scope is "construction" in the everyday sense. On commercial and government projects, glazing & facade work is typically assessed against AS 1288 (Glass in buildings, AS 2047) Windows and doors, and NCC weatherproofing, and the ITP is how you show each requirement was actually verified.
What hold points should a Glazing & Facade ITP include?: At minimum: subframe alignment inspection, structural glazing cure verification and water penetration test (if specified). Hold points belong wherever a defect would be concealed by following work or expensive to put right, so work stops until the nominated party signs. Your specification or the principal's QA plan may add more.
Which standards apply to glazing & facade inspections?: The references most glazing & facade ITPs cite are AS 1288 (Glass in buildings, AS 2047) Windows and doors, and NCC weatherproofing. Always check the project specification as well, it frequently calls up extra requirements, or a specific edition, on top of the standard.
Can I use an AI-generated glazing & facade ITP on a real project?: Yes, as a starting point. Generate the glazing & facade ITP for your scope, then review it against your contract and specification, especially the hold points, like subframe alignment inspection. Run it through HoldPoint for digital sign-offs, photos, and branded PDFs, and have your QA manager or superintendent approve the final version before it goes to site.

Related industries

More Construction & trades ITP Generators

Concrete ITP Generator

Generate a free concrete Inspection & Test Plan (ITP) with AI. Covers pre-pour checks, reinforcement inspection, hold points, and AS 3600 compliance. PDF in seconds.

Generate

Civil Construction ITP Generator

Generate a free civil construction ITP with AI. Covers earthworks, drainage, road pavement, kerb and channel, and pipe pressure testing. PDF in seconds.

Generate

Structural Steel ITP Generator

Generate a free structural steel ITP with AI. Covers fabrication, welding inspection, bolt tensioning, surface prep, and AS 4100 compliance. PDF in seconds.

Generate

Waterproofing ITP Generator

Generate a free waterproofing ITP with AI. Covers membrane application, substrate prep, flood testing, and AS 4654 compliance. PDF in seconds.

Generate

Formwork ITP Generator

Generate a free formwork ITP with AI. Covers shoring, propping, pre-pour inspection, and stripping schedules. PDF in seconds.

Generate

Earthworks ITP Generator

Generate a free earthworks ITP with AI. Covers cut and fill, compaction testing, subgrade preparation, and geotechnical hold points. PDF in seconds.

Generate

Browse all 91 industries →

Need to manage ITPs across a live project?

The free generator builds a single ITP. HoldPoint gives you the full workflow, templates, digital sign-offs, photo attachments, audit trails, and automatic PDF generation for every document on every project.

Continue with my ITP in HoldPoint Generate my Glazing & Facade ITP

14 days free. No credit card to start.